Jump to content
Toggle sidebar
JookWiki
Search
Create account
Log in
Personal tools
Create account
Log in
Pages for logged out editors
learn more
Contributions
Talk
Navigation
Main page
Recent changes
Random page
All pages
Help about MediaWiki
Tools
What links here
Related changes
Special pages
Page information
Editing
Blind electronics
(section)
Page
Discussion
English
Read
Edit
Edit source
View history
More
Read
Edit
Edit source
View history
Warning:
You are not logged in. Your IP address will be publicly visible if you make any edits. If you
log in
or
create an account
, your edits will be attributed to your username, along with other benefits.
Anti-spam check. Do
not
fill this in!
== Touching components == Tactility is the name of the game when it comes to navigating the world blind. The same is true for electronics. However there are various risks: === Hot components === Electricity creates heat, sometimes at temperatures where touching will cause a risk of burn. I would say there's two categories of heat to deal with: Controlled and uncontrolled. Controlled heat is what you would expect from a functioning design; Heat is an enemy to electronics too as it can damage components or change power consumption. A working design found in a manufactured product control heat using heat dissipation devices such as heat sinks. My recommendation on dealing with these components is to be careful as if you're touching something like a plate or a cup: * Touch it briefly to see how hot it is then decide whether to touch it again * Use the back of your hand to touch if needed * Power off and wait for components to cool if possible Uncontrolled heat happens due to a fault or bad design. The danger from this heat is that it's unexpected and results in a burn or fire. Usually you can detect uncontrolled heat through the following methods: * Touching a component (can result in burns, not recommended) * Smell from melted plastic or melting components I do want to make it clear that heat here comes from passing current through components. If you suspect something is going wrong, remove the current source (usually by just turning the device off) to avoid causing more heat. Batteries can be especially problematic in this case if there's no way to stop the current and thus heat. If you're using batteries make sure there's safety measures in place to stop the current, such as a fuse. === Powered components === Touching a component can potentially add you to a circuit. Depending on what type of circuit this is this may do nothing, it may damage the component, or it may damage you. There are two particular categories of circuits you should watch out for: Low voltage and high voltage. The human body does not conduct much electricity at low voltage (I'll use 12 volts as my conservative definition here) so it's unlikely you'll damage yourself by touching a component. It is possible to damage components by unintentional paths between components. There main technique to avoid this is to touch only the ground parts of the circuit such as metal USB or Ethernet shields. High voltage is a different story (I'll define it as over 50 volts here) as your body may conduct enough electricity to shock you. Do not touch high voltage components. If you're unsure, don't touch the component at all. It will not be an enjoyable experience and it will accomplish nothing. === Charged components === Components like batteries or capacitors can hold charge despite a device being turned off. Everything in the 'powered components' section above applies to these components as they are effectively still on. Removing batteries is likely possible, but capacitors are trickier. Capacitors can't hold charge long term like batteries. Most capacitors will discharge after a few seconds if not sooner. Touching the ends of low voltage capacitors with a finger can use your body to safely discharge the capacitor. The danger comes from large high voltage capacitors. Do not touch high voltage capacitors. === Electro-static discharge === The human body has the ability to act as a high voltage capacitor an deliver large shocks to electronic components. These shocks aren't large amounts of energy but still have the ability to damage components. Discharging these shocks may result in a light shock or no shock at all. The solution here is to use an anti-static wrist strap and anti-static mat, with both of these connected to a common ground that connects to an earthed point in your house, or earthed appliance like a desktop computer case. This ensures that the components, you and your environment all share a common voltage level and dissipate capacitance.
Summary:
Please note that all contributions to JookWiki are considered to be released under the Creative Commons Zero (Public Domain) (see
JookWiki:Copyrights
for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource.
Do not submit copyrighted work without permission!
To edit this page, please answer the question that appears below (
more info
):
Who owns this wiki?
Cancel
Editing help
(opens in new window)