AMD Geode/Video 1: Difference between revisions
m (Jookia moved page Geode Repair/Video to AMD Geode/Video: Troubleshooting is in another section) |
(→Tools: Add tools) |
||
Line 42: | Line 42: | ||
* Scarlett Solo with a VXLR adapter | * Scarlett Solo with a VXLR adapter | ||
* Rode Lavalier GO microphone | * Rode Lavalier GO microphone | ||
* | *[[Gophert NPS-1601]] power supply | ||
* [[protech QM1571]] multimeter | |||
* Siglent SDS1102CML+ oscilloscope | * Siglent SDS1102CML+ oscilloscope | ||
* Pinecil soldering iron | * Pinecil soldering iron |
Revision as of 09:46, 12 February 2022
See the parent article for details about what's happening in the video.
Because of prolonged production time I'm going to release what I have recorded so far as part 1 before I start with part 2.
Footage was shot from November 21 2021 through November 30 2021.
Editing was done from December 2021 through February 2022.
(That's assuming I finish this month.)
Mistakes
Overall I made the following mistakes during production:
- I didn't write a script
- I didn't film any usable B-roll
- I didn't make any kind of time for interjections
- There's no soft transitioning between scenes
- I didn't lock exposure on a bunch of clips
- I didn't white balance clips properly
- I didn't know what type of clips I needed in advance
- I didn't even know what type of video I was making
Achievements
As a counter to mistakes, here's some things I did do well:
- I filmed enough stuff to get the video done
- The video doesn't require a technical background to understand
- Listening doesn't lose important details
Workflow
By the end of production my workflow looked like this:
- Insert clips in to rough order and length
- Record voice-over in Audacity
- Match the audio up with the clips
- Tighten the timings a bit until things feel more natural
Most of the time and hesitancy of editing goes in to me not wanting to do the voice-over.
Tools
I used the following tools to make this video:
- Pentax K-5 camera
- Scarlett Solo with a VXLR adapter
- Rode Lavalier GO microphone
- Gophert NPS-1601 power supply
- protech QM1571 multimeter
- Siglent SDS1102CML+ oscilloscope
- Pinecil soldering iron
- Logitech C270 camera as a microscope
- Kdenlive 19.12 (newer versions can't export WebM VP8)
- Audacity for recording and cleaning audio
- Aegisub for subtitles
- Inkscape for title cards and other text overlay
Overall progress
To do
- Post: Re-do voiceover for consistency
- Post: Audio mixing
- Post: Music?
- Post: Subtitles
- Post: Release
- Post: Wiki page, all details
Done
- Scene: Introduction
- Scene: Board showoff
- Scene: Powering the board
- Scene: RAM
- Scene: BIOS removal
- Scene: Battery removal
- Scene: Keyboard
- Scene: Surprise cat
- Scene: Ethernet
- Scene: Breadboard serial cable
- Scene: VGA probing
- Scene: VGA board check
- Scene: SD card over IDE attempt
- Scene: Molex USB connector
- Scene: USB powering
- Scene: USB measurement
- Scene: VREF on datasheet, VGA schematics on OLPC
- Scene: Looking for VREF
- Scene: Probing BGA
- Scene: Null modem cable (Didn't film, just show eBay image)
- Scene: CompactFlash (Show eBay image)
- Scene: DOS (Didn't film, add to wiki?)
- Scene: Linux and VGA
- Scene: Probing VGA again
- Scene: Solder mess-up
- Post: Test viewing
- Post: Insert mention of original IBM computer in intro for context
- Post: Outro/ending/credits
- Post: Fix badly drawn schematic (Kdenlive doesn't like JPEGs)
- Post: Note about audio gear
- Post: Note about scope and webcam
Part 2
- eeePC comparison
- Investigate BIOS hunch
- Investigate capacitor hunch