AMD Geode/Video 3: Difference between revisions

Latest revision as of 06:59, 30 December 2023

This page is about the Repairing an AMD Geode: Part 3 video.

This video is about how I messed up, and fixing VGA brightness.

See AMD Geode/Video 3/Script for a textual description of the video.

Footage was shot from March 2022 through July 2023.

Editing was started on July 2023 and ended December 30 2023.

Workflow[edit | edit source]

I attempted to save my time and sanity by editing and subtitling the video first while writing the script then recording the voice over last. As a rule of thumb it seems each line of narration tends to be around 4 seconds.

I did attempt to produce the video in Blender but quickly went back to Kdenlive and Inkscape.

I did the subtitles during editing with Kdenlive and also smothered a lot of text on the video so it can be watched without subtitles.

In the end it seemed the format of the video was very similar to a slideshow presentation, but with a separate script and video elements. Maybe next video I should try to use a slideshow program that can export to HTML or something, then use Kdenlive to stack it together and add some videos.

Overall progress[edit | edit source]

Done[edit | edit source]

Chapter: Accessibility notice
Chapter: Recount
Chapter: Lessons learned
Chapter: Writing code
Chapter: Measurement
Chapter: Repair
Chapter: BIOS editing
Chapter: Ethernet removal
Proof read: Accessibility notice
Proof read: Recount
Proof read: Lessons learned
Proof read: Writing code
Proof read: Measurement
Proof read: Repair
Proof read: BIOS editing
Proof read: Ethernet removal
Chapter: BIOS flashing
Proof read: BIOS flashing
Chapter: Credits
Proof read: Credits
Voice over

@@ Line 1: / Line 1: @@
-Video 3 will be about fixing the network adapter I screwed up at the end of part 2. A quick detour.
+This page is about the [https://www.youtube.com/watch?v=tg0Zq2urKWc Repairing an AMD Geode: Part 3] video.
-== Scenes plan ==
+This video is about how I messed up, and fixing VGA brightness.
-Rough order of the video goes here:
-Mention failure:
+See [[AMD Geode/Video 3/Script]] for a textual description of the video.
-* I shouldn't have just touched random joints
+Footage was shot from March 2022 through July 2023.
-* I shouldn't have used too big an iron
-* I shouldn't have used solder braid
-Desoldering attempt 1:
+Editing was started on July 2023 and ended December 30 2023.
-* Document I spent 40 minutes badly heating the chip
+== Workflow ==
-* No plastic melted though
+I attempted to save my time and sanity by editing and subtitling the video first while writing the script then recording the voice over last. As a rule of thumb it seems each line of narration tends to be around 4 seconds.
-* Show clean up and flux residue
-Pin inspection:
+I did attempt to produce the video in Blender but quickly went back to Kdenlive and Inkscape.
-* Unbend pins
+I did the subtitles during editing with Kdenlive and also smothered a lot of text on the video so it can be watched without subtitles.
-* Inspect which are still connected
-* Compare to data sheet
-* Conclude we need to desolder
-Desoldering attempt 2:
+In the end it seemed the format of the video was very similar to a slideshow presentation, but with a separate script and video elements. Maybe next video I should try to use a slideshow program that can export to HTML or something, then use Kdenlive to stack it together and add some videos.
-* Larger nozzle
+== Overall progress ==
-* Higher temperature
-* Hard to see when unleaded solder melts
-* Clip of me removing an STM32 chip
-* Footage missing
-* Show desoldered network chip
-* Show cleanup of board
-* Show cleanup of chip and desoldered resistor
-Inspection:
+=== Done ===
-* No lifted pads outside existing ones
+* Chapter: Accessibility notice
-* The pads were never connected?!
+* Chapter: Recount
-* I should have checked it with a meter!
+* Chapter: Lessons learned
-* TODO: check pins
+*Chapter: Writing code
+*Chapter: Measurement
-Pad replacement:
+* Chapter: Repair
+* Chapter: BIOS editing
-* TODO: Add back pads that we need to connect
+* Chapter: Ethernet removal
+* Proof read: Accessibility notice
-Re-solder:
+*Proof read: Recount
+*Proof read: Lessons learned
-* TODO: Remove old solder
+*Proof read: Writing code
-* TODO: Solder back the resistor
+*Proof read: Measurement
-* TODO: solder the chip in place
+*Proof read: Repair
+*Proof read: BIOS editing
-Testing:
+*Proof read: Ethernet removal
+*Chapter: BIOS flashing
-* TODO: Install Debian Linux and try the Ethernet port
+*Proof read: BIOS flashing
+*Chapter: Credits
+*Proof read: Credits
+*Voice over
+[[Category:Projects]]