AMD Geode/Video 2: Difference between revisions
(→Overall progress: More work on the video) |
m (→Postponed for part 3: Fix list) |
||
(6 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
This is | This page is about the [https://www.youtube.com/watch?v=lJdBrTLBwpo Repairing an AMD Geode: Part 2] video. | ||
This video | This video goes over the soldering work between part 1 and the future part 3 where we're back to diagnostics. | ||
Footage was shot late March 2022, but only edited sporadically in August 2022 and Jan 2023. I really wasn't enjoying trying to write and talk over a 15 minute video where I just solder badly. | |||
I decided in early May 2023 to scrap the voice-over and just put some music over it. This managed to get the video released. | |||
== Video explanation == | |||
I filmed this almost of the video as a continuos 6 hour session, with 4 hours being soldering. This was not a good idea. In fact, the entire video is filled with almost entirely bad ideas. | |||
Here's a broad listing of takeaways you should have: | |||
* Don't solder for more than an hour at a time | |||
* Take breaks when you're frustrated | |||
* Perform each action with a plan and stop if it fails | |||
I failed almost all of these and instead tried to brute force through the process. Trying to continue a project that requires thought and attention after burning through those 15 minutes in did not work. | |||
Specific mistakes in the video: | |||
* I used too large a tip for most of it | |||
* I removed an imperfect pad instead of soldering on to it | |||
* I didn't use my too small pad strips as I thought running wire would be easier | |||
* I didn't tin the copper pads I made | |||
* I tried to use overcoat to bond pads to the board | |||
* I wanted to use tape to hold the pads down while heating but I didn't cut it too size and lifted the new pads | |||
* I spent way too long setting the pads and adding epoxy | |||
* I didn't remove the wire enamel before soldering | |||
* I didn't tape down the inductors and wires while soldering | |||
* I went around to 'touch up' random joints without a plan | |||
* I used the wrong iron shape to touch up the network IC joints | |||
* I couldn't get a solder blob to flow and added braid instead, creating more thermal mass | |||
Things I actually did well in the video: | |||
* I cleaned up the flux mess as I went | |||
* I fixed the VGA port | |||
* I used nail polish to coat the exposed network IC pins | |||
Mistakes outside of the video: | |||
* I misplaced the SMD capacitors I was going to solder | |||
I think I learned a lot. I felt really bad about having this video to show for it, but I think I did okay all things considered. | |||
== Overall progress == | == Overall progress == | ||
Line 9: | Line 51: | ||
* Editing: Scrubbed through and cut up all the needed footage | * Editing: Scrubbed through and cut up all the needed footage | ||
* Editing: Decided on scope of video | * Editing: Decided on scope of video | ||
*Editing: Cut the video down to an appropriate size | |||
*Editing: Added music and rendered | |||
*Wiki: Video explanation | |||
* | |||
* | |||
* | |||
=== Postponed for part 3 === | === Postponed for part 3 === | ||
Line 21: | Line 59: | ||
* Clarify mistake about video schematic | * Clarify mistake about video schematic | ||
* Probe ESD diodes | * Probe ESD diodes | ||
*Look at DAC code briefly | *Look at DAC code briefly | ||
*Test mode | *Test mode | ||
*Contact cleaner | *Contact cleaner | ||
*DAVdd measurement and fix | *DAVdd measurement and fix | ||
=== Scrapped === | |||
*Write script based on video segments | |||
*Explain each attempt | |||
*Voice-over | |||
[[Category:Projects]] | [[Category:Projects]] |
Latest revision as of 13:07, 19 August 2023
This page is about the Repairing an AMD Geode: Part 2 video.
This video goes over the soldering work between part 1 and the future part 3 where we're back to diagnostics.
Footage was shot late March 2022, but only edited sporadically in August 2022 and Jan 2023. I really wasn't enjoying trying to write and talk over a 15 minute video where I just solder badly.
I decided in early May 2023 to scrap the voice-over and just put some music over it. This managed to get the video released.
Video explanation[edit | edit source]
I filmed this almost of the video as a continuos 6 hour session, with 4 hours being soldering. This was not a good idea. In fact, the entire video is filled with almost entirely bad ideas.
Here's a broad listing of takeaways you should have:
- Don't solder for more than an hour at a time
- Take breaks when you're frustrated
- Perform each action with a plan and stop if it fails
I failed almost all of these and instead tried to brute force through the process. Trying to continue a project that requires thought and attention after burning through those 15 minutes in did not work.
Specific mistakes in the video:
- I used too large a tip for most of it
- I removed an imperfect pad instead of soldering on to it
- I didn't use my too small pad strips as I thought running wire would be easier
- I didn't tin the copper pads I made
- I tried to use overcoat to bond pads to the board
- I wanted to use tape to hold the pads down while heating but I didn't cut it too size and lifted the new pads
- I spent way too long setting the pads and adding epoxy
- I didn't remove the wire enamel before soldering
- I didn't tape down the inductors and wires while soldering
- I went around to 'touch up' random joints without a plan
- I used the wrong iron shape to touch up the network IC joints
- I couldn't get a solder blob to flow and added braid instead, creating more thermal mass
Things I actually did well in the video:
- I cleaned up the flux mess as I went
- I fixed the VGA port
- I used nail polish to coat the exposed network IC pins
Mistakes outside of the video:
- I misplaced the SMD capacitors I was going to solder
I think I learned a lot. I felt really bad about having this video to show for it, but I think I did okay all things considered.
Overall progress[edit | edit source]
Done[edit | edit source]
- Editing: Scrubbed through and cut up all the needed footage
- Editing: Decided on scope of video
- Editing: Cut the video down to an appropriate size
- Editing: Added music and rendered
- Wiki: Video explanation
Postponed for part 3[edit | edit source]
- Clarify mistake about shunt schematic
- Clarify mistake about video schematic
- Probe ESD diodes
- Look at DAC code briefly
- Test mode
- Contact cleaner
- DAVdd measurement and fix
Scrapped[edit | edit source]
- Write script based on video segments
- Explain each attempt
- Voice-over